Notes Switch travel diagram
  Contact closed
  Contact open
  Setting range
  Break point
  Positive opening sequence/- angle
VS  adjustable range of NO contact
  adjustable range of NC contact
N   after travel
Deutsch  English  Francais  Nederlands  Italiano  Español  Português  Suomi  Svenska  Norsk  Dansk  Polska  日本語  Türkiye  中文  Português-br  
Home ->
Solenoid interlock  ->  AZM 200D  ->  AZM 200D-ST2-T-1P2P2P
 Add Product to the basket. 
AZM 200D-ST2-T-1P2P2P
NOTICE: Available until 2020.12.31 (substitute: AZM201D)
• Thermoplastic enclosure
• Electronic contact-free, coded system
• Max. length of the sensor chain 200 m
• 3 LEDs to show operating conditions
• Sensor technology permits an offset between actuator and interlock of ± 5 mm vertically and ± 3 mm horizontally
• Intelligent diagnosis
• Manual release
• Guard locking monitored

Ordering details
Product type descriptionAZM 200D-ST2-T-1P2P2P
Article number101217604
EAN Code4030661412917
Safety guard monitoring Y1 and Y2
StandardsEN ISO 13849-1, IEC 61508, IEC 60947-5-3
PLbis e
Control categorybis 4
PFH value4.0 x 10-9/
SILbis 3
Mission time20 Years
Locking monitoring Y3 and Y4
StandardsEN ISO 13849-1, IEC 61508, IEC 60947-5-3
PLup d
Control categorybis 3
PFH value1.0 x 10 −7
SILup 2
Mission time20 Years
Global Properties
Permanent lightAZM 200D
StandardsEN 60947-5-1, IEC 61508, EN ISO 13849-1, IEC 60947-5-3
Compliance with the Directives (Y/N) Yes
Suitable for safety functions (Y/N)Yes
Active principleinductive
Duty cycle100
- Material of the housingsPlastic, glass-fibre reinforced thermoplastic
Housing coatingNone
Guard locking monitored (Y/N)Yes (Sicherheitsausgänge Y3, Y4)
Actuator monitored (Y/N)Yes (Sicherheitsausgänge Y1, Y2)
Idle assignable pushbutton and LED (Y/N)No
Reaction time≤ 60
Duration of risk< 120
Time to readiness< 4000
Recommended actuatorAZ/AZM 200-B1
Mechanical data
Design of electrical connectionConnector M12, 8-pole
Cable section
- Min. Cable section0,25
- Max. Cable section1.5
AWG-Number23 - 15
Mechanical life≥ 1.000.000 operations
noticeAll indications about the cable section are including the conductor ferrules.
restistance to shock30 / 11
Resistance to vibration10 … 55 HZ, Amplitude 1 mm
Emergency unlocking device (Y/N)No
Manual release (Y/N)Yes
Emergency release (Y/N)No
Latching force30
Clamping force2000
Max. Actuating speed≤ 0,2
Cable length200
Ambient conditions
Ambient temperature
- Min. environmental temperature−25
- Max. environmental temperature+60
Storage and transport temperature
- Min. Storage and transport temperature−25
- Max. Storage and transport temperature+85
Protection classIP67 to IEC/EN 60529
Protection ratingII
Air clearances and creepage distances To IEC/EN 60664-1
- Rated impulse withstand voltage0,8
- Overvoltage categoryIII
- Degree of pollution3
Electrical data
Number of auxiliary contacts0
Number of safety contacts4
Cross circuit/short circuit recognition possible (Y/N)Yes
Power to unlockYes
Power to lockNo
Supply voltage
- Min. supply voltage20.4 V DC
- Max. supply voltage26.4 V DC
Switch frequency1
Rated insulation voltage32 V DC
Operating current1.2 A
Utilisation categoryDC-12, DC-13
No-load current0,5 A
Device insulation
- screw or spade terminals≤ 4 A if used in accordance with UL 508
- Connector M12≤ 2 A
- Connector M23≤ 4 A
Electrical data - Safety outputs
Safety outputsY1, Y2, Y3, Y4
Fuse ratingshort-circuit proof, p-type
Rated operating voltage0 … 4 under Supply voltage
Residual current≤ 0,5
Operating currentY1, Y2: 0,25 A
Y3, Y4: 0,1 A
Utilisation categoryDC-13
Electrical data - Diagnostic output
Serial diagnostics (Y/N)No
Fuse ratingp-type, short-circuit proof
Operating current0,1 A
Utilisation categoryDC-13: 24 V / 0,05 A
Wiring capacitance for serial diagnostics-
diagnostic signalsguard door closed
Operating principle of the diagnostic outputThe short-circuit proof diagnostic output OUT can be used for central visualisation or control tasks, e.g. in a PLC.
noticeThe diagnostic output is not a safety-relevant output!
Residual current through outputs Y3, Y4, OUT:IY3+ IY4 + OUT ≤ 0,1 A
Electrical data - Solenoid control IN
Rated operating voltage- 3 … 5 ( Low)
15 … 30 ( High)
Operating currenttypically 10 / 24 , dynamically 20
LED switching conditions display
LED switching conditions display (Y/N)Yes
LED switching conditions display
- Supply voltagegreen LED
- switching conditionyellow LED
- Error functional defectred LED
Explosion protection categories for gasesNone
Explosion protected category for dustsNone
Dimensions of the sensor
- Width of sensor40
- Height of sensor220
- Length of sensor50
As lons as the actuating unit remains inserted in the solenoid interlock, the unlocked safety guard can be relocked. The safety outputs then will be enabled again; opening the safety guard therefore is not required.
Included in delivery
Included in deliveryAZM 200
Triangular key
Actuators must be ordered separately.

K.A. Schmersal GmbH & Co. KG, Möddinghofe 30, D-42279 Wuppertal
The data and values have been checked throroughly. Technical modifications and errors excepted.
Generiert am 20.09.2019 - 05:59:28h Kasbase 3.3.0.F.64I