Notes Switch travel diagram
  Contact closed
  Contact open
  Setting range
  Break point
  Positive opening sequence/- angle
VS  adjustable range of NO contact
  adjustable range of NC contact
N   after travel
Deutsch  English  Francais  Nederlands  Italiano  Español  Português  Suomi  Svenska  Norsk  Dansk  Polska  日本語  Türkiye  中文  Português-br  
• Actuation from front
• Non-contact principle
• with bias magnet
• Long life
• Metal enclosure
• Actuating distance up to 60 mm depending on actuating magnet and version
• Design Ø 10.7 mm
• with central mounting
• With pre-wired cable

Preferred typ
Ordering details
Product type descriptionBN 12-RZ/V
Article number101186837
EAN Code4030661335360
Global Properties
Permanent lightBN 12
Compliance with the Directives (Y/N) Yes
suitable for elevators (Y/N)Yes
Mountingcentral with threated flange M12 x 1
Active principleMagnetic drive
- Material of the housingsMetal film
- Material of the cable mantleLiYY
Housing construction formcylinder, thread
Recommended actuator2 x BP 10, BP 34, BP 20, BP 31, BP 11, BP 12, BP 21, BP 22 N, BP 22 S, BE 20
- Lift switchgearBP 10, 2 x BP 10, BP 15, BP 34
Mechanical data
Design of electrical connectionCable
Cable length1
Conductors2 x 0,25
Mechanical life10.000.000 operations
Electrical lifetime1.000.000 … 10.000.000 operations
Actuating planesfront side
Switch distance3 … 45
2 x BP 10 = 3 mm
BP 34 = 15 mm
BP 20 = 10 mm
BP 31 = 10 mm
BP 11 = 15 mm
BP 12 = 20 mm
BP 21 = 45 mm
BP 22 N = 35 mm
BP 22 S = 35 mm
BE 20 = 10 mm
- noticeActuating distance up to 45 mm depending on actuating magnet and version

The specifications with regard to the switching distances apply to the actuation of the individually mounted devices without ferromagnetic influence. Any change of the
distance, positive either negative, is possible due to ferromagnetic interference. When multiple actuating magnets are used, the mutual
interference must be observed.
Type of actuationMagnet
restistance to shock30 / 11
Resistance to vibration10 … 55 HZ, Amplitude 1 mm
Bounce duration0,15
Latching (Y/N)Yes
bias magnet (Y/N)Yes
Actuating speed18
Switching point accuracy± 0,25 mm
Ambient conditions
Ambient temperature
- Min. environmental temperature−25
- Max. environmental temperature+70
Protection classIP67 to IEC/EN 60529
Electrical data
Design of control elementbistable contact
Number of snap-in contacts1
Switching time - Close0,35
Switching time - Open30
Switch frequency< 300
Dielectric strength580
Switching voltage200
Switching current1 A
Switching capacity30 /
Design of control outputReed contakts
LED switching conditions display
LED switching conditions display (Y/N)No
Explosion protection categories for gasesNone
Explosion protected category for dustsNone
Dimensions of the sensor
- Length of sensor71
- Diameter of sensor10.7
The opening and closing functions depend on the direction of actuation, the actuating magnets and the polarity of the actuating magnets.
When the switches and actuators come together, the colours must coincide: Red (S) to red (S) and green (N) to green (N). This does not apply to the bistable contact.
The switch is to be mounted on iron with a non-magnetic layer of at least 20 mm.
Included in delivery
Actuators must be ordered separately.

Note Diagram
  positive break NC contact
  no active
  Normally-open contact
  Normally-closed contact
Switch travel diagram

Notes Switch travel diagram
  Contact closed
  Contact open
  Setting range
  Break point
  Positive opening sequence/- angle
VS  adjustable range of NO contact
  adjustable range of NC contact
N   after travel

K.A. Schmersal GmbH & Co. KG, Möddinghofe 30, D-42279 Wuppertal
The data and values have been checked throroughly. Technical modifications and errors excepted.
Generiert am 18.02.2019 - 03:41:15h Kasbase 3.3.0.F.64I