Notes Switch travel diagram
  Contact closed
  Contact open
  Setting range
  Break point
  Positive opening sequence/- angle
VS  adjustable range of NO contact
VÖ  adjustable range of NC contact
N   after travel
Deutsch  English  Francais  Nederlands  Italiano  Español  Português  Suomi  Svenska  Norsk  Dansk  Polska  日本語  Türkiye  中文  Português-br  
  

Datasheet Datasheet

Click to enlarge image
• With pre-wired cable
• Non-contact principle
• Long life
• Actuation from side
• Actuating surface and direction of actuation marked by switch symbol
• with bias magnet
• Construction form Ø 13 mm
• Thermoplastic enclosure
• Actuating distance up to 60 mm depending on actuating magnet and version
• with central mounting

 
Preferred typ
 
Ordering details
 
Product type descriptionBN 65-RZ - Ordering suffix
Article number101055800
EAN Code4030661009490
eCl@ss27-27-01-04
 
Approval
 
Approval
 
Global Properties
 
Permanent lightBN 65
Standards-
Compliance with the Directives (Y/N) Yes
suitable for elevators (Y/N)Yes
Mountingcentral with threated flange
Active principleMagnetic drive
Materials
- Material of the housingsPlastic, glass-fibre reinforced thermoplastic
- Material of the cable mantleH03VV-F
Housing construction formcylinder smooth
Weight70
Recommended actuatorBP 10N, BP 10S, 2 x BP 10N, 2 x BP 10S, BP 15N, BP 15S, 2 x BP 15/2N, 2 x BP 15/2S, BP 34N, BP 34S, BP 20N, BP 20S, BP 31N, BP 31S, BP 11N, BP 11S, 2 x BP 11N, 2 x BP 11S, BP 12N, BP 12S, 2 x BP 12N, 2 x BP 12S, BP 21N, BP 21S, 2 x BP 21N, 2 x BP 21S, BE 20N, BE 20S
- Lift switchgearBP 10, 2 x BP 10, 2 x BP 15/2, BP 15, 2 x BP 15, BP 34
 
Mechanical data
 
Design of electrical connectionCable
Cable length1
Conductors2 x 0,75
AWG-Number18
Mechanical life1.000.000.000 operations
Electrical lifetime1.000.000 … 1.000.000.000 operations
Switching frequency300/
Actuating planesActuation from side
Switch distance15 … 60
BP 10N = 15 mm
BP 10S = 15 mm
2 x BP 10N = 20 mm
2 x BP 10S = 20 mm
BP 15N = 17 mm
BP 15S = 17 mm
2 x BP 15/2N = 22 mm
2 x BP 15/2S = 22 mm
BP 34N = 10 ... 30 mm
BP 34S = 15 ... 30 mm
BP 20N = 25 mm
BP 20S = 25 mm
BP 31N = 25 mm
BP 31S = 25 mm
BP 11N = 15 mm
BP 11S = 15 mm
2 x BP 11N = 25 mm
2 x BP 11S = 25 mm
BP 12N = 20 mm
BP 12S = 20 mm
2 x BP 12N = 10 ... 30 mm
2 x BP 12S = 10 ... 30 mm
BP 21N = 15 ... 45 mm
BP 21S = 15 ... 45 mm
2 x BP 21N = 20 ... 60 mm
2 x BP 21S = 20 ... 60 mm
BE 20N = 20 mm
BE 20S = 20 mm
- noticeActuating distance up to 60 mm depending on actuating magnet and version

The specifications with regard to the switching distances apply to the actuation of the individually mounted devices without ferromagnetic influence. Any change of the
distance, positive either negative, is possible due to ferromagnetic interference. When multiple actuating magnets are used, the mutual
interference must be observed.
Type of actuationMagnet
restistance to shock30 g, on sine wave oscillation
resistant to vibration30 g, on sine wave oscillation
Resistance to vibration10 … 55 HZ, Amplitude 1 mm
Bounce duration0,3 … 0,6; 3
Latching (Y/N)Yes
bias magnet (Y/N)Yes
Tightening torque for nuts22 300
Actuating speed18
Switching point accuracy± 0,25 mm
 
Ambient conditions
 
Ambient temperature
- Min. environmental temperature−25
- Max. environmental temperature+75
Protection classIP67 to IEC/EN 60529
 
Electrical data
 
Design of control elementbistable contact
Number of snap-in contacts1
Switching time - Close0,3 … 1.5
Switching time - Open0,5
Switch frequency< 300
Dielectric strength> 600 (50 )
Switching voltage250
Switching current3 A
Switching capacity120
 
Outputs
 
Design of control outputReed contakts
 
LED switching conditions display
 
LED switching conditions display (Y/N)No
 
ATEX
 
Explosion protection categories for gasesNone
Explosion protected category for dustsNone
 
Dimensions
 
Dimensions of the sensor
- Length of sensor103
- Diameter of sensor13
 
notice
 
The opening and closing functions depend on the direction of actuation, the actuating magnets and the polarity of the actuating magnets.
When the switches and actuators come together, the colours must coincide: Red (S) to red (S) and green (N) to green (N).
This does not apply to the bistable contact.
 
Included in delivery
 
Actuators must be ordered separately.
 
Diagram
 


Note Diagram
  positive break NC contact
  active
  no active
  Normally-open contact
  Normally-closed contact
 
Switch travel diagram
 


Notes Switch travel diagram
  Contact closed
  Contact open
  Setting range
  Break point
  Positive opening sequence/- angle
VS  adjustable range of NO contact
VÖ  adjustable range of NC contact
N   after travel
 
Ordering suffix
 
The applicable ordering suffix is added at the end of the part number of the safety switch.
Order example: BN 65-RZ-2m
...-2m
K.A. Schmersal GmbH & Co. KG, Möddinghofe 30, D-42279 Wuppertal
The data and values have been checked throroughly. Technical modifications and errors excepted.
Generiert am 23.06.2019 - 19:52:01h Kasbase 3.3.0.F.64I